Obituary: Dr. Otto Langenegger – Kloss (22 April 1938 — 19 February 2023)

I am sorry to inform you of the passing of Dr. Otto Langenegger, who peacefully left us on 19 February, 2023 surrounded by his family, aged 84. 

Dr Langenegger was the pioneer of rapid handpump corrosion. His seminal publications in 1989 and 1994 set the foundation for all that followed in trying to understand and address this phenomenon.

In his eulogy, he was poignantly referred to as a “nomad around water”. He grew up, in humble surroundings, close to Lake Constance in eastern Switzerland, the youngest of six siblings. 

His thirst for discovering and learning could not be quenched by his apprenticeship as a radio technician in Winterthur. He was a through-and-through scientist and researcher, moving between subjects throughout his life, and building on the learning from one area as he branched into another. Together with his wife Dorothea, he moved to work in Canada for several years, from where he was able to, amongst other experiences, be part of an expedition to the Arctic, an exposure that he relished for the rest of his life. 

Dr. Langenegger and his wife, with their two sons Urs and Thomas, moved back to Switzerland, and he completed his first PhD at the University of Bern in 1973. But he was soon on the move again, this time to Ethiopia, where he worked as a Hydrogeologist with the Christoffel Mission. He was fascinated by the people and culture, and was saddened to have to leave in 1976 due to the difficult political situation at the time.

Dr. Langenegger was not long back in Switzerland, before heading off to Africa in 1981, initially to Ghana, where he worked for the World Bank on the pioneering water well drilling and handpump installation project of its time in West Africa. This position, and the subsequent assignment based out of Abidjan, took him to Burkina Faso, Cote d’Ivoire, Ghana, Mali and Niger.

As a keen observer and compassionate man, Dr Langenegger was both intrigued and appalled by the ‘red water’ problem, coupled with corroding and failing handpumps that he observed in many parts of West Africa during his field work. And so, he set out to understand the causes. Initially using his own allowances to test water quality, he diligently researched this issue. One of his colleagues from the time told me that he stayed in the cheaper hotel in Kumasi – saving money for testing, and filling the bathtub with his tests. He also had his wife, Dorothea, cook plantain with different concentrations of iron-rich water from the rapidly corroding handpumps to see what happened to them. They changed colour.

Anyone working on handpump corrosion is familiar with Otto Langenegger’s seminal publications (1989 and 1994), which have provided the foundation for all that has followed on this topic. His second PhD was in fact on Handpump Corrosion. 

After returning to Switzerland in 1989, Dr. Langenegger set up his private consultancy practice, working out of his home in Gais, Appenzell. Overlooked by snow-capped Alpstein mountains, his interest in water found an outlet in learning about the blue coloured snow, high on the slopes. And so once again, this through-and-through researcher set about observing, measuring and interpreting. I would say that Dr. Langenegger’s, keen interest and thirst for knowledge in relation to water was insatiable. 

It was 2019 that Dr. Langenegger, who would soon to be known to me by the informal address simply as Otto, contacted me. He had found my own report on Rapid handpump corrosion in Burkina Faso and beyond and wanted to know more. Otto was both disgusted that the corrosion problem had not been fully addressed (after more than 30 years), but was also pleased that it was at least being looked at again. Unbeknown to me previously, he lived just a few stops along the train line from St. Gallen where I am based! 

Otto had been out of touch with the water supply world in Africa for a long time, but had, now and then, searched for what may have followed on from his work on handpump corrosion. And so he was aware of the presentation entitled  ‘New signs of an old Problem’ at the WaTer Conference in Oklahoma in 2015 by Vincent Casey, Lawrence Brown and Jake Carpenter.

Over the last two and a half years that Otto and I were able to share, he followed all of the ongoing efforts and work to address rapid handpump corrosion – the issue which he has pioneered in the 1980s. He was delighted to be able to talk about the subject, and, researcher that he was, always asked such pertinent questions and put forward ideas. 

Throughout his long illness, and even as he grew weak towards the end of his magnificent life, he always wanted to hear the latest news. His delight to hear that the corroding handpumps in Ghana had been replaced in the 1990s is something that will always remain with me. “It was not all for nothing” he remarked, fist in the air, referring to his efforts over 30 years ago.

Dr. Otto Langenegger will be much missed. May he Rest in Peace.

He leaves behind a large family: 

Urs and Marika Langenegger-Bohse with their children Tabea, Dominik and Eliane.

Thomas and Anita Langenegger Vogel, with their children Samuel, Jonas, Elias, Rahel and Salome.

His sister, Rosa Massey-Langenegger.

Addressing rapid handpump corrosion: the story of the Ghana Modified India Mark II

In 1983, I moved to live and work in Ghana – some 40 years ago now. Back then, I was the regional supervisor on the 3000 Well Maintenance Unit in Southern and Central Ghana which was funded by the German Development Service under the Rural Water Supply programme. The project was a pioneer of its time, and included drilling boreholes alongside the installation and testing of handpumps in six of Ghana’s regions, as well as the Nanumba district, Northern Region.

We initially installed India Mark II and Moyno pumps, before dropping the Moyno due to technical problems. However, we soon realised that the India Mark II pumps faced corrosion issues. Investigation and testing (as documented by Langennegger, 1989 and Langenegger, 1994) found that the Galvanised Iron components (rods and riser pipes), when installed in water with low pH, had a propensity to rapidly corrode – leading to discolouration of the water and affecting taste, but also causing the pumps to fail prematurely as the rods broke and riser pipes developed cracks and holes and even fell into the borehole. The envisaged idea of maintenance by communities, with assistance from mechanics who could reach villages by motorcycle, was simply not feasible with such installations. Another significant issue related to corrosion of hand pump parts was the water contamination and bad taste of the water. As a result, the water coloured the food and therefore caused the  population to stop using the borehole water and forced them to go back to unsafe water sources

We, therefore, had to seek alternatives. This involved field testing and collaborating with the Materials Testing Institute of the University of Darmstadt.

We looked into replacing the galvanised iron components with stainless steel. To ensure the pipes were light, we considered using 3 – 3.5 mm thick pipes, and used a threading that at the time was used in the drilling industry , known as the “rope thread”. Although Atlas Copco had patented this threading type at the time, it was later manufactured in India after the Atlas Copco design period (patent) ended.

Figure 1: Rope thread (Claus Riexinger)

The pump rods presented some challenges as well, since the AISI Stainless Steel grade 316 that we were using was subject to breakage, including the threaded parts. In collaboration with our partners at the University of Darmstadt, we were able to find ways to make this grade of stainless steel more elastic by adding 2-3 % Molybdenum. Other issues with the rods related to the use of rolled thread, which we learned was more durable than cut thread. Incorporating these materials and techniques, we were able to reduce the rod diameter from 12 mm down to 10.8mm, resulting in lighter rods which did not corrode. The only drawback was that the threads could not be cut in the field, but this was not such an issue, as there was no need to cut them when they were installed, or upon maintenance.

Figure 2: Pump installation (Claus Riexinger)

After switching to stainless steel riser pipes, we encountered another issue: -galvanic corrosion between the pipe and the water tank. This type of corrosion occurs when two dissimilar materials come into contact in solution. It was yet another challenge! Fortunately, we were able to solve this problem by replacing the existing flange with a new one made of stainless steel with an insulating gasket, into which the riser pipe could be screwed and prevent any further galvanic corrosion.

Figure 3: Ghana Modified India Mark II Handpump – water tank, spout and flange

After conducting extensive testing and collaborating with the University of Darmstadt over a period of around 4 years, we managed to solve the problem of rapid corrosion of handpumps in Ghana. The improved pump design came to be known as the Ghana Modified India Mark II, and was officially adopted by the Government of Ghana in the 1990s. Its specifications can be downloaded here.

Designing and publishing the specifications for a new pump is one thing, but the other is ensuring that these are adhered to.  A series of meetings with government, donors, and NGOs working in the water sector in the 1990s, led to the agreement to no longer use Galvanised Iron. All stakeholders were on board with the change.

Of particular importance was the tremendous support and buy-in of the major donor at the time – KfW (Germany). They agreed to pay for the increased costs of the Ghana Modified Pump on new installations, which at the time was about three times more expensive than the version using Galvanised Iron.  KfW also supported the rehabilitation and replacement of the pumps that had previously been installed using Galvanised Iron. As a result, we were able to remove and replace the corroded installations systematically, rather than addressing the issue in a piecemeal manner.

It is estimated that over 4,500 Ghana Modified India Mark II handpumps had been installed in Ghana by the time I left the 3000 Well Maintenance Unit in 1992.  Anecdotally, I would say that 90% were working, and of the 10% out of use, they were down for maintenance/repair.

KfW took this design to Cameroon, while Danida took it to Burkina Faso and Zambia. I am not fully aware of what happened next, but I do know that ensuring the quality of stainless steel was a problem in Burkina Faso.

I am very pleased to see that Ghana Modified India Mark II handpumps are now available through the Rural Water Supply Network (RWSN), and hope that these can be of use to other countries that are struggling to overcome the rapid handpump corrosion problem.

Figure 4: Example factory inspection Modified India MKII (Claus Riexinger)

However, I have a work of caution too. Although specifications, standards, and clear procurement documents are essential, they are rendered meaningless in the absence of inspection. During my time with the 3000 Well Maintenance Unit and later as an independent consultant, I traveled to India and other places for pre-shipment inspections. I also oversaw the rejection of consignments from India and Europe due to poor quality or manufacturing mistakes. And so, I urge all of you involved in handpump procurement and installation to make sure that you ensure the quality, especially through inspection and material testing.

Ghana Modified India Mark II Drawings and Specifications

More information about Ghana Modified India Mark II (external website)

About the author: Claus Riexinger is a rural WASH expert and freelance consultant with over forty years of experience in development cooperation with Government organisations, private companies, and development agencies mainly in Botswana, Lesotho, Malawi, Germany, India, Tanzania, and Ghana.

Photo credits: Claus Riexinger

New REAL-Water activity: Water Sustainability in Southern Madagascar

REAL-Water to coordinate data and actions for the sustainable development of water resources in arid Southern Madagascar.

In Madagascar, there are significant disparities in access to essential water and sanitation services. Currently, only about half of the population (54.4%) has access to vital water services, and just over 10% have access to necessary sanitation services. The situation is particularly challenging in Southern Madagascar, where various development issues, such as population growth, changes in land use, and worsening dry-season water shortages, are present. These difficulties are exacerbated by poverty, which hinders water resource development, leads to poor infrastructure, and contributes to food insecurity. 

To guide regional programming that considers the development and humanitarian requirements, USAID Madagascar has commissioned REAL-Water to assess water resources and infrastructure needs. The program will entail specific activities, including a literature review of water development activities, data collection on existing and planned water infrastructure, analyses of remaining water resources and infrastructure needs, and planning for future investments.

Topographical map of Southern Madagascar.
The six districts of interest covered in the assessment are shown on an I-digital elevation model (from the Shuttle Radar Topography Mission). Small gray and green polygons indicate areas of human settlement (“Settlement Extents”) from the GRID3 DATA HUB. Each settlement extent type (built-up area, small settlement area, and hamlet) is included, with built-up areas depicted in green).

Re-blogged from Aquaya. RWSN is proud to be partner in the REAL-Water programme leading on engagement.

Online learning on groundwater – strengthening capacity in African member states and beyond

Professional Drilling Management & Groundwater Resources Management

Thanks to funding from the Federal Institute for Geosciences and Natural Resources (BGR) in Germany, 2022 saw Ask for Water GmbH, together with the Africa Groundwater NetworkCap-Net UNDP and several other partners (see below) develop and run two online courses on groundwater. The courses strengthened the capacity of staff of governments, NGOs, the private sector and academia in African member states and beyond. 

The courses, hosted by Cap-Net UNDP, and offered free of charge to participants, were entitled Groundwater Resources Management and Professional Drilling Management. Each course was specifically developed for professionals working on these issues, or responsible for decision making.

Face to face training course on drilling supervision
in Sierra Leone (Source: Kerstin Danert)

Professional Drilling Management Course

Drilled water wells are vital to achieving universal clean drinking water, providing safe, affordable, reliable and available water sources. To ensure that the water wells or boreholes are built to last, they must be drilled, developed and completed in a professional manner. Key elements of a professional drilling sector are robust procurement, contract management, siting, borehole design, construction, and supervision. Furthermore, the management of the groundwater resources must also be considered and support provided to long-term maintenance if services are to last. Unfortunately, in many countries it is difficult to develop skills in these areas due to a lack of training and mentoring opportunities.

The 2022 online course on Professional Drilling Management provided participants with a comprehensive overview of the different aspects of drilling management, specifically (i) groundwater data and siting; (ii) procurement and contract management (including costing and pricing; (iii) borehole drilling and supervision and (iv) legal and institutional frameworks. In the last of five modules, participants were encouraged to reflect upon and share actions that they as individuals and as organisations could take to raise drilling professionalism in the context in which they work. From the 781 people who applied for the course, 314 were selected, of which 209 were active participants. A total of 162, equivalent to 78% of the active participants passed the course. 

You can access the 2022 course report, manual and key training materials here.

If you would like to learn about what alumni of previous online courses on Professional Drilling Management have done with their knowledge, check out the short film below or the short report of their testimonials.

Groundwater Resources Management Course

An estimated 50% of the global and 75% of the African population rely on groundwater for their drinking water supplies. Groundwater supports social and economic development and will become increasingly important in the face of climate change, as groundwater resources are often less affected than surface water by climate change impacts. If groundwater is to provide reliable, safe and sustainable water supplies now and for future generations, the resource must be well-managed. This requires consideration of the entire system of policies & laws, strategies & guidance, monitoring & management as well as investments & projects. Good groundwater management needs sound capacities in water authorities. But at same time, as many elements of groundwater management fall in other sectors, a general understanding of groundwater management principles in sectors like agriculture and urban planning is key for its successful implementation. 

The 2022 online course on groundwater resources management provides participants with a comprehensive overview of the multiple factors that impact upon groundwater. It was a self-paced course and was hosted on the virtual campus of Cap Net/UNDP.

The course comprised 5 modules; each with a short introduction, goal, learning objectives and orientation video, as well as mandatory videos and reading materials: 

  • Module 1: Characterization of Aquifer Systems from a Management Perspective
  • Module 2: Groundwater monitoring and data/information management & communication
  • Module 3: Groundwater quality and source water protection
  • Module 4: Groundwater regulation, licensing, allocation and institutions for aquifer management
  • Module 5: Transboundary aquifers in Africa: Approaches and mechanisms

You can access the 2022 course report, manual and key training materials here.

Artesian well near Lake Chad, Chad
(Source: Moustapha Diene

What next?

The Rural Water Supply Network (RWSN), Ask for Water GmbH, the Africa Groundwater Network (AGW-Net), Cap-Net UNDP and partners would like to offer these courses on an annual basis. We are currently looking for sponsors/funders to make this possible. In case you are interested, please contact us via  info@rural-water-supply.net.

Should we manage to get these courses off the ground, we will announce them through the Africa Groundwater NetworkCap-Net UNDP and the Rural Water Supply Network as well via LinkedIn.

Funded by

Partners